Q.01

Can polypropylene be used in food packaging under FDA rules?

Yes. Polypropylene is cleared for food packaging under 21 CFR 177.1520 (Olefin polymers). The rule says the listed olefin polymers "may be safely used as articles or components of articles intended for use in contact with food, subject to the provisions of this section" [1]. The clearance only covers resin that meets the section's identity, specification and adjuvant conditions. Calling a material "polypropylene" is not enough.

What the resin must meet (§177.1520)

  • Identity, (a)(1):

    • Polypropylene is defined as "basic polymers manufactured by the catalytic polymerization of propylene" (item 1.1a).
    • Propylene homopolymer made with a metallocene catalyst is listed separately (item 1.1b) [1].
  • Specifications, (c), items 1.1a and 1.1b:

    • Density 0.880-0.913.
    • Melting point 160-180 °C for 1.1a and 150-180 °C for 1.1b.
    • Maximum n-hexane extractable fraction 6.4% at reflux temperature.
    • Maximum xylene soluble fraction 9.8% at 25 °C [1].
  • Noncrystalline polypropylene is restricted:

    • Item 1.2 allows it "for use only to plasticize polyethylene."
    • Item 1.3 allows it to plasticize item 1.1 polypropylene. That plasticized polypropylene may contact only food Types I, II, IV-B, VI-B, VII-B and VIII (Table 1 of §176.170(c)) [1].
  • Additives, (b): the polymer "may contain optional adjuvant substances required in the production." These can be substances:

    • permitted by Parts 170-189;
    • GRAS;
    • covered by a prior sanction; or
    • listed in the (b) table, many of which carry their own limits on level, food type and conditions of use.

    For example, one listed resin is allowed only up to 25% in blends with item 1.1 polypropylene, and only under specified food types and Conditions of Use B-H or D-G [1].

  • Finished article, (f) and (g):

    • If the olefin polymer is part of the food-contact surface of an article regulated elsewhere in Parts 174-178 or §179.45, it "shall comply with any specifications and limitations" of that regulation.
    • §177.1520 does not apply to olefin polymers used in adhesives under §175.105 [1].

General conditions (21 CFR 174.5)

  • Use must follow good manufacturing practice:
    • no more than is "reasonably required" for the technical effect in the article;
    • no intended technical effect in the food itself;
    • purity "suitable for its intended use."
  • A clearance does not exempt the packaging from the rest of the FD&C Act. The example given is odour or taste transfer that makes food unfit under section 402(a)(3).
  • A clearance does not make the substance a permitted direct food additive [2].
  • §174.5(d) also lists effective FCNs as a lawful route to clearance [2].

FDA inventory cross-check

  • FDA's Inventory of Food Contact Substances Listed in 21 CFR (05/04/2026 edition) lists polypropylene (CAS 9003-07-0) under §§175.105 (adhesives), 175.300 (resinous and polymeric coatings) and 177.1520 [3].
  • Amorphous polypropylene is listed under §§175.105, 177.1200, 177.1520, 178.1005 and 179.45 [4].

Grades outside the regulation's specifications: these have been cleared company by company through FCNs, which apply only to the notifier's own material and carry their own limits. Examples:

  • FCN 2311 (effective 10/12/2023): polypropylene homopolymer as a base resin for all food types under Conditions of Use B-H, or as an additive at no more than 30 wt% in §177.1520 polypropylene. Not for infant formula or human milk [5].
  • FCN 1912: low-melting polypropylene (melting point 65-80 °C) at no more than 50 wt% in polyolefin articles complying with §177.1520. Excludes infant formula and human milk [6].
  • FCN 1033: polypropylene homopolymer as a carrier or processing aid at no more than 5% of the finished article [7].

In practice, for a compliance statement you need the resin supplier to confirm the grade meets §177.1520 items 1.1a or 1.1b. Every additive, colorant and process aid also needs its own clearance, and its food-type and temperature limits must cover your actual use.

Approach: I read the current eCFR text of 21 CFR 177.1520 and 174.5, and checked FDA's Inventory of Food Contact Substances Listed in 21 CFR and its Inventory of Effective Food Contact Substance Notifications (08/31/2026 edition). I did not review the colorant rule (§178.3297) or every individual adjuvant listing in §177.1520(b).

Q.02

What evidence should I request from my resin supplier?

You need evidence for four things: that the base resin meets 21 CFR 177.1520, that every additive in the grade has its own clearance, that the clearance covers your food types and processing conditions, and that the regulatory basis is right if the grade relies on an FCN rather than §177.1520. Ask for each one tied to the exact grade and regulation item, not a generic "FDA compliant" statement.

1. Which item the resin falls under

  • Ask for a written statement naming the §177.1520 item.
    • Item 1.1a: polypropylene, "basic polymers manufactured by the catalytic polymerization of propylene".
    • Item 1.1b: propylene homopolymer "with a metallocene catalyst" [1].
  • A copolymer grade falls under the separate copolymer items (3.x), which have different limits.
  • If the grade contains noncrystalline polypropylene, ask whether it is used under item 1.3. That item limits the plasticized resin to food Types I, II, IV-B, VI-B, VII-B and VIII [1].

2. Test data against the paragraph (c) specifications, by the paragraph (d) methods Under §177.1520(a), the polymers must meet the (c) specifications "when tested by the methods described in paragraph (d)" [1]. Ask for results, or a summary report, for each of these:

Specification (items 1.1a / 1.1b)Method in §177.1520(d)
Density 0.880-0.913ASTM D1505-68 (density-gradient)
Melting point 160-180 °C (1.1a) / 150-180 °C (1.1b)ASTM D2117-82 (hot-stage microscopy)
n-hexane extractable fraction no more than 6.4% at reflux(d)(3)(i), 2-hour reflux
Xylene soluble fraction no more than 9.8% at 25 °C(d)(4)(i)

[1]

These methods apply "to the basic polymer in film form not exceeding 4 mils in thickness" [1]. Check that the data was produced on that kind of sample.

3. A full list of additives with the clearance for each

  • Under §177.1520(b), the resin "may contain optional adjuvant substances". These must be:
    • permitted by Parts 170-189;
    • GRAS;
    • covered by a prior sanction; or
    • on the (b) list [1].
  • For each antioxidant, nucleator, slip agent, catalyst residue or process aid, ask for:
    • the clearance it relies on (a CFR section, an FCN number or GRAS);
    • the level used;
    • any limits on food type or conditions of use attached to that clearance.
  • Many (b) entries carry their own limits. One processing aid, for example, is capped at 1.0% and its finished polymers may be used only under Conditions of Use B through H [1].
  • If the supplier won't disclose full composition, ask for a list of the clearance citations, or a statement that each additive's limits cover your use.

4. Colorants and masterbatch, if any

  • Colorants must "conform to the description and specifications" in §178.3297 [8].
  • Many entries are grade-specific. For example, C.I. Pigment Yellow 183 is allowed at no more than 1% in polypropylene meeting §177.1520(c) items 1.1a, 1.1b, 1.2 or 1.3, and only under Conditions of Use E through G [8].
  • Ask the masterbatch supplier for each pigment's identity, its clearance and the level in the finished article.

5. Food types and conditions of use your application needs Ask for the cleared scope to be stated using FDA's food types (Table 1 of §176.170(c), Types I-IX) and conditions of use (Table 2, A to H). Condition A is high-temperature heat-sterilized (over 212 °F). Condition H is reheating in the container [9]. Check the narrowest additive or colorant limit against your actual use, for example retort, hot fill or microwave reheating.

6. If the grade relies on an FCN rather than §177.1520

  • Ask for the FCN number and confirm the supplier is the listed manufacturer.
  • FCN entries name both the notifier and the manufacturer/supplier. FCN 2311, for example, lists Hunan Liwei New Material and Huizhou Leaptop Advanced Materials as manufacturers [5].
  • Check the FCN's own limits. FCN 2311 allows Conditions of Use B through H and excludes infant formula and human milk [5].

7. Supporting statements tied to §174.5

  • Good manufacturing practice: additives are used at no more than is "reasonably required" for their technical effect.
  • Purity: components are "of a purity suitable for its intended use."
  • Both come from §174.5(a) [2].
  • Odour and taste: a clearance does not relieve the packaging from section 402(a)(3) if it taints food [2]. Odour and taste checks on your food are your own responsibility, not the resin supplier's.

What the supplier's evidence can't cover: §177.1520(f) requires the finished article to meet the limits of any other Part 174-178 regulation that applies to it [1]. The resin documents don't address your converting additives, inks, adhesives or layers made of other materials.

Approach: I read the current eCFR text of 21 CFR 177.1520, 174.5, 176.170(c) and 178.3297, and checked an example in FDA's Inventory of Effective Food Contact Substance Notifications. I did not review every individual adjuvant in §177.1520(b) or the colorant list in full.

Q.03